Adblue-emulaator mudelitele Volvo FH4, FM4, FMX4 Euro 6

Adblue emulaator (on/off) Volvo FH4, FM4, FMX4 Euro 6 jaoks (2014-2021). Täielik SCR, NOx & DPF eemaldus. Paigaldub 10-15 minutiga, ilma programmeerimiseta.

1–3: €320 · 4–5: €260 · 6+: €200

  • Sobivad mudelid: Volvo FH4, FM4, FMX4
  • Aastavahemik: 2014–2021
  • Emulaatori tüüp: On/Off Switch
  • Kaubamärk: Can Logic
  • Garantii: 2 years

See seade asendab

  • SCR / ECU juhtplokk
  • DPF heitgaaside süsteem
  • Adblue pumba moodul
  • Rõhuandur
  • Adblue tasemeandur
  • Temperatuuriandur
  • NOx enne katalüsaatorit
  • NOx pärast katalüsaatorit

Kirjeldus

Kaal: 0.03kg

Bränd: Can Logic

Emulaatori tüüp: On/Off Switch

Raha tagasi garantii: 14 days

2-aastane garantii

Tasuta veebipõhine tehniline tugi meie klientidele

Professionaalne Adblue emulaator, juhend kaasas

Valmistatud parima kvaliteediga autodetailidest

Seadme info

Toote kood: ME-FH4-E6-ON

Tootetüüp: Adblue emulaator

Mootori tüüp: VOLVO

Ühilduv ECU: EMS

VOLVO Seeria: 4 series

Heitmenorm: EURO 6

Veoautode jaoks ehitatud 2014 - 2021

Ühilduvad mudelid: FH4, FM4, FMX4

Paigaldus

Step one:

Emulator is to be connected to the ACM plug. Please find ACM module (this is located right hand side of the frame) Remove/unplug ACM plug.

Step two:

Please connect emulator as shown below. (connect to wires from ACM plug) Power connections:

- BROWN wire from emulator connect to PIN 58 (- Negative)

- RED wire from emulator connect to PIN 60 (+ Positive/power)

- Cut PIN3 wire and connect the GREY wire from the emulator to the wire going into the plugt, not to the end that goes oward the truck. (+ Ignition/power)

CAN LINE Connections:

CAN 1 - DO NOT cut these wires, Connect the wires in parallel.

- WHITE wire from emulator connect to PIN1

- BLUE wire from emulator connect to PIN5

CAN 2 - DO NOT cut these wires, Connect the wires in parallel.

- GREEN wire from emulator connect to PIN10

- YELLOW wire from emulator connect to PIN14

Step three:

Please disconncect ACM ECU

To do this please cut wire from PIN 3 and isolate the ends.

Step four:

Once emulator has been installed turn ignition on and check Adblue level gauge is showing, this would indicate installation has been successful.

LED Light indicators:

- Ignition OFF - No LED

- Ignition ON (Emulator) - RED LED, BLUE blinking

- Ignition ON (Original SCR) - GREEN LED, BLUE blinking

ON/OFF switch function instructions:

1. Turn ignition ON (do not start the engine).

2. Press the accelerator pedal fully down and hold it pressed for 10 seconds.

3. Release the accelerator pedal and turn ignition OFF. Wait for 10 seconds.

4. Start the engine.

If done correctly, the system should switch to the desired mode.

Seotud tooted