Emulator Adblue do Volvo FH4, FM4, FMX4 Euro 6

Emulator Adblue (on/off) do Volvo FH4, FM4, FMX4 Euro 6 (2014-2021). Pełne wyłączenie SCR, NOx i DPF. Montaż w 10-15 minut, bez programowania.

1–3: 1 405 zł · 4–5: 1 145 zł · 6+: 880 zł

  • Kompatybilne modele: Volvo FH4, FM4, FMX4
  • Zakres lat: 2014–2021
  • Typ emulatora: On/Off Switch
  • Marka: Can Logic
  • Gwarancja: 2 years

To urządzenie zastępuje

  • Sterownik SCR / ECU
  • System wydechowy DPF
  • Moduł pompy Adblue
  • Czujnik ciśnienia
  • Czujnik poziomu Adblue
  • Czujnik temperatury
  • NOx przed katalizatorem
  • NOx po katalizatorze

Opis

Waga: 0.03kg

Marka: Can Logic

Typ emulatora: On/Off Switch

Gwarancja zwrotu pieniędzy: 14 days

2 lata gwarancji

Bezpłatne wsparcie techniczne online dla naszych klientów

Profesjonalny emulator Adblue, instrukcja w zestawie

Wyprodukowane z najwyższej jakości komponentów automotive

Informacje o urządzeniu

Kod produktu: ME-FH4-E6-ON

Typ produktu: Emulator Adblue

Typ silnika: VOLVO

Zgodne ECU: EMS

VOLVO Seria: 4 series

Norma emisji: EURO 6

Dla ciężarówek z roku 2014 - 2021

Zgodne modele: FH4, FM4, FMX4

Instalacja

Step one:

Emulator is to be connected to the ACM plug. Please find ACM module (this is located right hand side of the frame) Remove/unplug ACM plug.

Step two:

Please connect emulator as shown below. (connect to wires from ACM plug) Power connections:

- BROWN wire from emulator connect to PIN 58 (- Negative)

- RED wire from emulator connect to PIN 60 (+ Positive/power)

- Cut PIN3 wire and connect the GREY wire from the emulator to the wire going into the plugt, not to the end that goes oward the truck. (+ Ignition/power)

CAN LINE Connections:

CAN 1 - DO NOT cut these wires, Connect the wires in parallel.

- WHITE wire from emulator connect to PIN1

- BLUE wire from emulator connect to PIN5

CAN 2 - DO NOT cut these wires, Connect the wires in parallel.

- GREEN wire from emulator connect to PIN10

- YELLOW wire from emulator connect to PIN14

Step three:

Please disconncect ACM ECU

To do this please cut wire from PIN 3 and isolate the ends.

Step four:

Once emulator has been installed turn ignition on and check Adblue level gauge is showing, this would indicate installation has been successful.

LED Light indicators:

- Ignition OFF - No LED

- Ignition ON (Emulator) - RED LED, BLUE blinking

- Ignition ON (Original SCR) - GREEN LED, BLUE blinking

ON/OFF switch function instructions:

1. Turn ignition ON (do not start the engine).

2. Press the accelerator pedal fully down and hold it pressed for 10 seconds.

3. Release the accelerator pedal and turn ignition OFF. Wait for 10 seconds.

4. Start the engine.

If done correctly, the system should switch to the desired mode.

Powiązane produkty