Volvo FH4, FM4, FMX4 Euro 6용 Adblue 에뮬레이터

Volvo FH4, FM4, FMX4 Euro 6용 Adblue 에뮬레이터 (on/off) (2014-2021). SCR, NOx 및 DPF 완전 제거. 프리미엄 품질, 방수. 10-15분 만에 장착, 프로그래밍 불필요.

1–3: ₩479,650 · 4–5: ₩390,825 · 6+: ₩302,000

  • 호환 모델: Volvo FH4, FM4, FMX4
  • 연식 범위: 2014–2021
  • 에뮬레이터 유형: On/Off Switch
  • 상표: Can Logic
  • 보증: 2 years

이 장치는 다음을 대체합니다

  • SCR / ECU 제어 장치
  • DPF 배기 시스템
  • Adblue 펌프 모듈
  • 압력 센서
  • Adblue 레벨 센서
  • 온도 센서
  • 촉매 전 NOx
  • 촉매 후 NOx

설명

무게: 0.03kg

브랜드: Can Logic

에뮬레이터 유형: On/Off Switch

환불 보증: 14 days

2년 보증

당사 고객을 위한 무료 온라인 기술 지원

전문 Adblue 에뮬레이터, 설명서 포함

최고급 자동차용 부품으로 제조

장치 정보

제품 코드: ME-FH4-E6-ON

제품 유형: Adblue 에뮬레이터

엔진 유형: VOLVO

호환 ECU: EMS

VOLVO 시리즈: 4 series

배출 표준: EURO 6

제조된 트럭 2014 - 2021

호환 모델: FH4, FM4, FMX4

설치

Step one:

Emulator is to be connected to the ACM plug. Please find ACM module (this is located right hand side of the frame) Remove/unplug ACM plug.

Step two:

Please connect emulator as shown below. (connect to wires from ACM plug) Power connections:

- BROWN wire from emulator connect to PIN 58 (- Negative)

- RED wire from emulator connect to PIN 60 (+ Positive/power)

- Cut PIN3 wire and connect the GREY wire from the emulator to the wire going into the plugt, not to the end that goes oward the truck. (+ Ignition/power)

CAN LINE Connections:

CAN 1 - DO NOT cut these wires, Connect the wires in parallel.

- WHITE wire from emulator connect to PIN1

- BLUE wire from emulator connect to PIN5

CAN 2 - DO NOT cut these wires, Connect the wires in parallel.

- GREEN wire from emulator connect to PIN10

- YELLOW wire from emulator connect to PIN14

Step three:

Please disconncect ACM ECU

To do this please cut wire from PIN 3 and isolate the ends.

Step four:

Once emulator has been installed turn ignition on and check Adblue level gauge is showing, this would indicate installation has been successful.

LED Light indicators:

- Ignition OFF - No LED

- Ignition ON (Emulator) - RED LED, BLUE blinking

- Ignition ON (Original SCR) - GREEN LED, BLUE blinking

ON/OFF switch function instructions:

1. Turn ignition ON (do not start the engine).

2. Press the accelerator pedal fully down and hold it pressed for 10 seconds.

3. Release the accelerator pedal and turn ignition OFF. Wait for 10 seconds.

4. Start the engine.

If done correctly, the system should switch to the desired mode.

관련 상품