Adblue emulators modeļiem Volvo FH4, FM4, FMX4 Euro 6

Adblue emulators (on/off) Volvo FH4, FM4, FMX4 Euro 6 (2014-2021). Pilnīga SCR, NOx un DPF atspējošana. Uzstādāms 10-15 minūtēs, bez programmēšanas.

1–3: €320 · 4–5: €260 · 6+: €200

  • Saderīgie modeļi: Volvo FH4, FM4, FMX4
  • Izlaiduma gadi: 2014–2021
  • Emulatora tips: On/Off Switch
  • Zīmols: Can Logic
  • Garantija: 2 years

Šī ierīce aizvieto

  • SCR / ECU vadības bloks
  • DPF izplūdes sistēma
  • Adblue sūkņa modulis
  • Spiediena sensors
  • Adblue līmeņa sensors
  • Temperatūras sensors
  • NOx pirms katalizatora
  • NOx pēc katalizatora

Apraksts

Svars: 0.03kg

Zīmols: Can Logic

Emulatora tips: On/Off Switch

Naudas atmaksas garantija: 14 days

2 gadu garantija

Bezmaksas tiešsaistes tehniskais atbalsts mūsu klientiem

Profesionāls Adblue emulators, instrukcijas pievienotas

Ražots no augstākās kvalitātes auto rūpniecības komponentiem

Ierīces informācija

Produkta kods: ME-FH4-E6-ON

Produkta tips: Adblue emulators

Motora tips: VOLVO

Saderīga ECU: EMS

VOLVO Sērija: 4 series

Emisiju standarts: EURO 6

Kravas auto, ražoti 2014 - 2021

Saderīgi modeļi: FH4, FM4, FMX4

Uzstādīšana

Step one:

Emulator is to be connected to the ACM plug. Please find ACM module (this is located right hand side of the frame) Remove/unplug ACM plug.

Step two:

Please connect emulator as shown below. (connect to wires from ACM plug) Power connections:

- BROWN wire from emulator connect to PIN 58 (- Negative)

- RED wire from emulator connect to PIN 60 (+ Positive/power)

- Cut PIN3 wire and connect the GREY wire from the emulator to the wire going into the plugt, not to the end that goes oward the truck. (+ Ignition/power)

CAN LINE Connections:

CAN 1 - DO NOT cut these wires, Connect the wires in parallel.

- WHITE wire from emulator connect to PIN1

- BLUE wire from emulator connect to PIN5

CAN 2 - DO NOT cut these wires, Connect the wires in parallel.

- GREEN wire from emulator connect to PIN10

- YELLOW wire from emulator connect to PIN14

Step three:

Please disconncect ACM ECU

To do this please cut wire from PIN 3 and isolate the ends.

Step four:

Once emulator has been installed turn ignition on and check Adblue level gauge is showing, this would indicate installation has been successful.

LED Light indicators:

- Ignition OFF - No LED

- Ignition ON (Emulator) - RED LED, BLUE blinking

- Ignition ON (Original SCR) - GREEN LED, BLUE blinking

ON/OFF switch function instructions:

1. Turn ignition ON (do not start the engine).

2. Press the accelerator pedal fully down and hold it pressed for 10 seconds.

3. Release the accelerator pedal and turn ignition OFF. Wait for 10 seconds.

4. Start the engine.

If done correctly, the system should switch to the desired mode.

Saistītie produkti